Your filter has settings. Let’s make them make sense.
Seven labels. One handle. A surprising amount of backyard confusion. Let’s turn that sand-filter valve from “please don’t touch it” into “okay, I know what that does.”
You wander over to the equipment pad and spot FILTER, BACKWASH, RINSE and a few other words that sound like instructions for a very expensive washing machine. Good news: there’s a logic to all of it. Better news: you don’t need to become a pool engineer to learn it.
By Ryan MuschDirector of Liquid Affairs, The FinPOOL SCHOOL · EQUIPMENT EDITION
Which filter are we talking about? A sand filter with a multiport valve, such as a Hayward Vari-Flo. Labels and layouts vary. This is not a cartridge-filter cleaning guide, and D.E. filters have different care requirements. Match the manual to your actual equipment.
“The handle picks the route. The sand catches the gross.”
— Ryan Musch, The Fin
THE SEVEN SETTINGS · PART ONE
Where does the water go?
Read the words on your valve—not the position on somebody else’s dial. These numbers are our reading order, not instructions to turn the handle clockwise.
01FILTER
The everyday setting. Not a personality test.
Water passes through the sand bed, leaves its dirt behind and returns to the pool. This is home base for normal filtration and regular vacuuming through the filter.
THE FIN TAKEMost of your swimming-season pump time belongs here. A running pump only filters when the water actually goes through the filter.
02BACKWASH
Give the dirt its eviction notice.
This reverses flow through the sand bed and sends trapped debris out the waste line. It cleans the filter—not the entire pool, your patio or your life choices.
THE FIN TAKERecord your clean-filter pressure. Backwash at the pressure increase specified in your exact filter manual, not an automatic “plus four” or a weekly calendar appointment.
03RINSE
The follow-through matters.
After backwashing, RINSE sends water through the sand in the normal filtering direction and out to waste. It helps settle the bed and flush leftover dirty water away instead of returning it to your pool.
THE FIN TAKEFollow your model’s rinse duration. Then stop the pump, return to FILTER and restart according to the equipment manual. Don’t skip the pump-off part.
04WASTE
Out of the pool. Out of the loop.
Water bypasses the sand and leaves through the waste line. It can lower the water level or carry heavy debris out while vacuuming, when appropriate for your pool.
THE FIN TAKEWatch the water level continuously. Stop before the intake draws air; never let the pump run dry. Don’t drain a pool without pool-specific guidance. Route discharge only where local rules allow.
THE SEVEN SETTINGS · PART TWO
Bypass. Stop. Put it to bed.
05RECIRCULATE
A scenic drive. No dirt collection.
Water goes through the valve and back to the pool without passing through the sand. It circulates, but it does not filter. Same pool. Different road.
THE FIN TAKEUse only when your equipment procedure or chemical label calls for it. Clarifiers and flocculants are not all alike; some need filtering, settling or vacuuming to waste. RECIRCULATE is not a universal “add chemicals” setting—or a substitute for sanitizer.
06CLOSED
Closed means closed.
This stops flow through the valve. It is not a super-filter setting, a pause button for the motor or an invitation to leave the pump running.
THE FIN TAKEKeep the pump OFF in CLOSED. A closed valve is not proof that equipment is depressurized or safe to open.
07WINTER
A parking spot. Not a force field.
On valves that provide it, the winterizing position helps water drain from the valve. Some handles park between operating positions; the exact placement depends on the valve.
THE FIN TAKEKeep the pump OFF. Follow the full pool, pump, filter and valve winterizing instructions. Turning one handle does not protect an entire system from freezing. Before spring startup, restore the proper operating setup.
THE ROUTINE · NOT A RACE
Backwash. Rinse. Back to business.
For routine cleaning of a compatible sand-filter setup, this is the big-picture sequence. Your equipment manual supplies the pressure trigger, run times and startup details. New sand and first startup can require a different procedure.
Start with your baseline. Note the clean-filter pressure under normal operating conditions. Use your model’s specified pressure increase to decide when to backwash. Unexpected flow or pressure changes deserve a check, not an extra turn of the handle.
Stop → BACKWASH → run as directed. Set up an approved discharge route first. With the pump off, select BACKWASH, then restart as the manual directs. Watch the sight glass or discharge for the required clarity and follow the specified duration.
Stop → RINSE → run as directed. Shut the pump off before selecting RINSE. Restart for your manual’s rinse cycle. Keep an eye on the pool level—both cycles send water away.
Stop → FILTER → restart properly. Shut off before returning the valve to FILTER. Follow the startup and air-relief instructions for your system. Check water level, normal flow and pressure; record the clean reading.
16HOURS / DAY
Give your filter a real shift.
The Fin recommends at least 16 hours of pump operation a day during swimming season, including daytime hours when the pool is in use. That’s our service recommendation—not a universal Hayward requirement. Your pool’s flow, conditions and equipment instructions still matter. Runtime never replaces proper filtration or sanitizer.
This story explains the settings; it is not a service manual. Confirm your valve and filter model before using cleaning or winterizing instructions. Not every valve has a labeled WINTER setting.
Manufacturer materials checked November 7, 2026 (CST). Ryan portrait supplied by The Fin; pool image reused from the existing FIN education library. See integration notes for asset provenance and technical review details.