Calcium hardness
The amount of dissolved calcium in the water. The right level protects pool equipment and plaster finishes from corrosion by keeping the water from pulling calcium out of pool walls (like plaster and grout). Too low causes etching and equipment corrosion. Too high causes cloudy water and scale buildup. Ideal range: 200–400 ppm.
Calcium hypochlorite
A powerful oxidizing chemical that cleans and sanitizes pool water. Often called cal-hypo.
Chelated copper
Copper algaecides that contain a special ingredient to keep the copper from staining the pool walls and floor or tinting the water.
Chloramines. The real “pool smell.”
Compounds containing chlorine and nitrogen. They form unintentionally when free chlorine binds to organic matter swimmers bring in, like sweat, oils and urine. That “chlorine smell”? It’s actually chloramines. High levels can irritate the eyes, nose and respiratory system. Shock treatment removes them.
Chlorinator
A mechanical or electrical device that dispenses chlorine at a controlled rate. Most often a tank, canister or floater filled with chlorine tablets.
Chlorine
The most widely used chemical for sanitizing water. It comes in several forms, including calcium hypochlorite. As a biocide, chlorine kills the bacteria and algae found in pools.
Read Ryan’s full story on chlorine →
Chlorine demand
The amount of chlorine needed to destroy algae, bacteria and other contaminants and still leave a stable free available chlorine (FAC) residual.
Chlorine lock. When your chlorine gets handcuffed.
A condition where a pool’s chlorine is rendered ineffective: the water won’t sanitize, and you get cloudy water or algae. It’s caused by too much cyanuric acid (CYA, also called stabilizer or conditioner), which binds to the chlorine molecules and neutralizes their sanitizing power.
CYA is essential for keeping the sun from burning off your chlorine, but too much of it (typically above 90–100 ppm) over-stabilizes the chlorine. The chlorine is handcuffed. 🚔 Your test strips may show plenty of chlorine, but the pool stays green or cloudy because the chlorine can’t kill bacteria effectively.
🧮 THE 7.5% RULETo prevent chlorine lock, keep free chlorine (FC) and CYA in balance. Your minimum FC should be about 7.5% of your CYA level. Example: CYA at 50 ppm → FC of at least 3.75 ppm.
🛠️ CYA TOO HIGH? FIXES- The easiest: drain and refill with fresh water.
- Switch to non-stabilized chlorine like calcium hypochlorite (cal-hypo) or liquid chlorine.
- Use a specialized CYA-reducer.
Chlorine residual
The chlorine left in the water after the chlorine demand has been satisfied. It’s what remains to kill new bacteria and algae that haven’t entered the pool yet.
Free chlorine. The active-duty germ fighter. CHLORINE [FREE CHLORINE]
The active sanitizer that kills bacteria and algae and keeps pool water safe and clean. When chlorine dissolves in water, it mainly releases hypochlorous acid (HOCl), a weak acid that actively kills pathogens. It destroys bacteria, viruses, algae and organic contaminants (like sweat, oil and urine) by attacking their cell walls.
For chlorine to work efficiently, keep the pH between 7.2 and 7.6 (7.8 at the very top end). If pH runs too high, chlorine loses its effectiveness. If pH is too low, it can irritate skin and eyes and may damage pool equipment.
FOUR TYPES OF POOL CHLORINE
💊 TABLETSCompressed 1″ or 3″ discs. They contain cyanuric acid to protect the chlorine from UV breakdown and dissolve slowly for a steady, continuous release of sanitizer. They usually sit in a chlorine floater on the pool’s surface or in a chlorinator.
🧃 LIQUIDTypically sold as 10–12.5% sodium hypochlorite. It acts very quickly and has no added stabilizer or calcium, so it’s a great choice for fast sanitizing or shocking the pool to clear up cloudy water.
🪣 POWDER / GRANULARIncludes calcium hypochlorite or dichlor. Highly concentrated and often used for periodic “shock” treatments that quickly break down heavy organic waste and algae blooms.
🧂 SALTWATER SYSTEMSA chlorinator uses electrolysis to turn dissolved salt (sodium chloride) into chlorine right on site.
The ideal range for chlorine in a standard outdoor pool is 2–4 ppm. If it drops below 1 ppm, the water risks turning cloudy or green.
Clarifier
A chemical that coagulates and neutralizes suspended particles in water, making them easier for the filter to remove.
Coagulant
An organic polyelectrolyte used to gather (coagulate) suspended particles in the water.
Combined available chlorine
Total available chlorine minus free available chlorine (TAC − FAC).
Conditioner
Also called stabilizer or cyanuric acid. It slows down sunlight’s breakdown of chlorine in the water. The minimum effective level is 20 ppm, as measured by a test kit. High levels of cyanuric acid (well above the ideal range; see Chlorine lock) slow down chlorine’s activity and effectiveness. Conditioner does not protect bromine from sunlight.
Copper algaecide
An algaecide that contains copper. Copper sulfate was one of the original copper algaecides. Too much copper in the water can cause green stains or green water. Newer copper algaecides contain an ingredient that prevents staining without affecting copper’s ability to kill algae. These special versions are called chelated copper algaecides.
Corrosion
The pitting and dissolving away of pool components, including filter housings, pump housings, mechanical seals, heater elements, metal fixtures, plaster and tile grout. Low pH, total alkalinity and/or calcium hardness can cause it.
Cyanuric acid CYA
Commonly called stabilizer or conditioner. It helps prevent the loss of free available chlorine in direct sunlight. Ideal range in a pool: 30–50 ppm.