The Fin pool, spa & hot tubs, Tulsa OK The Fin Get a quote

POOL CHEMISTRY · LEARNING WITH THE FIN

Saltwater pool systems. Make your own chlorine.

Say “saltwater” and your brain heads straight for the ocean. Your pool? Not so much. As cool as it would be to float around a backyard Mediterranean Sea, no, it won’t happen. Honestly, your saltwater pool doesn’t even have that much salt in it. Here’s how salt systems really work, what they’re great at, what they’re hard on, and how to keep yours happy.

Ryan Musch of The Fin on a lifeguard chair in front of a Malibu Barbie beach mural, owner of The Fin in Tulsa
By Ryan Musch Director of Liquid Affairs, The Fin Worth his salt 🧂

“As cool as it would be to float in a backyard Mediterranean Sea… no, it won’t.”

Ryan, Director of Liquid Affairs (and breaker of saltwater dreams)

① WAIT, IT’S STILL CHLORINE?

Salt in, chlorine out. Surprise!

Here’s the big one: a saltwater pool is NOT chlorine-free. Saltwater pools use the same basic chemistry to break down organic matter as a traditional chlorine pool.

The difference? Instead of adding chlorine to the pool yourself, you add salt. The water runs through a salt cell (the chlorine generator), which turns that salt into chlorine. In short, you’re making your own chlorine instead of buying it at the store.

THE SALT-TO-CHLORINE ROUND TRIP

Round and round it goes.

  1. 🧂 Salt
  2. ⚡ Salt cell
  3. 🫧 Chlorine
  4. 🧼 Cleans the water
  5. 🧂 Back to salt

After the chlorine does its job, it turns back into salt, and the cell gets to use it all over again.

② BENEFITS & DRAWBACKS

The good, the salty & the slightly corrosive.

THE GOOD STUFF

Why people love salt.

Easier on eyes, skin & hair

The stuff that makes most people want out of the chlorine game is much less of an issue with salt. Most swimmers find salt water easier on their eyes and skin, and it’s gentler on hair and swimsuits too.

Feels “softer”

Water in a saltwater pool tends to feel softer. Silky, even. Your skin will notice.

Fewer peaks and valleys

You still check your chemicals regularly, but you’ll usually make fewer adjustments because your sanitizer levels stay steadier.

Cheap salt that recycles itself

Salt costs very little, and it recycles itself. Congratulations: you’ve got a little sanitation factory in your backyard.

THE FINE PRINT

What salt is hard on.

A shiny stainless steel ladder going into a sparkling blue swimming pool
A bigger investment up front

A salt system costs more up front, but it usually pays for itself in maintenance, time and money. It may just take a few years.

Metal gives it the side eye

Your skin and hair will thank you for going salt. Your pool parts? They’ll give you the side eye. Salt water is harder on metal than fresh water and can slowly eat away at metal in and around your pool: ladders, patio furniture, handrails and the metal snaps on cousin Jimmy’s toupee.

Not quite set-it-and-forget-it

The salt cell needs a cleaning now and then (calcium loves to build up on it) and a replacement every few years. Salt pools also tend to push pH up over time, so keep that acid handy.

METAL’S BODYGUARD

Meet the sacrificial anode. A brave little hunk of zinc.

Corrosion isn’t the end of the world, and it’s no reason to write off saltwater. Because science is a heck of a drug, we’ve got a bodyguard for your metal: the sacrificial anode.

A sacrificial anode is a zinc device that protects metal parts from corrosion. Zinc gives up its ions faster than the other metals in your pool, so it goes first, sacrificing itself to save everything else. Zinc is a brave little guy. Hence the name.

~3 yrstypical anode lifespan
½replace it when it’s half eroded

Heads up: the anode only protects metal that’s connected and bonded to the pool. It can’t help things you move around, like metal patio furniture. For those, rinse and store is your only protection. The anode also has to be connected to the pool’s bonding wire and grounded. Let an electrician do it. ⚡

③ WHAT’S PPM?

Parts per million. The pool world’s favorite unit.

Parts per million (PPM): you’re going to see this a lot in the pool chemistry world. It’s the standard unit for how much of a dissolved substance (like free chlorine, total alkalinity or calcium hardness) is in the water. One PPM means one part for every million parts of water.

Thankfully, testing water isn’t too “sciencey.” Just look at the numbers and follow the directions. PPM matters because it’s the difference between too much and not enough. You want enough chlorine to kill harmful bacteria, viruses and algae, but not so much that it’s rough on the humans. Find the middle ground.

  • FREE CHLORINE

    2–4 ppm

    The stuff doing the actual cleaning.

  • TOTAL ALKALINITY

    80–120 ppm

    The Pool Pilot Evolve manual’s sweet spot is 80–100.

  • CALCIUM HARDNESS

    200–400 ppm

    Too low is corrosive. Too high is scaly.

  • CYANURIC ACID (STABILIZER)

    30–50 ppm

    Yes, salt pools still need it. It’s chlorine’s sunscreen. 30–50 is the Pool Pilot Evolve manual’s number, but saltwater pools generally do better a bit higher, around 60–80 ppm. Think SPF 60.

  • SALT

    3,500–4,500 ppm

    For the Pool Pilot Evolve. Other brands often aim lower, so check your manual.

Good news: these ideal ranges are pretty universal in pool chemistry (CYA is the one salt pools like a little higher). Write them on a sticky note, stick it to the pump. Done.

④ UNDERSTANDING CHLORINE

Yes, you have a chlorine pool. We won’t tell your friends.

Sorry, but when you look at the science, you do have a chlorine pool. You just make it a different way. So the basic rules of chlorine sanitation still apply. Chemically speaking, there are three forms of chlorine you need to know:

Free chlorine (FC). The hero.

This is the chlorine you want. It does the actual sanitizing. Free chlorine is highly reactive, and once it’s in the pool it loves to combine with organic matter. It quickly attacks pathogens and other swimmer waste (if you know what we mean).

Combined chlorine. The used-up hero.

When free chlorine teams up with the icky stuff, it chemically changes and becomes combined chlorine. Combined chlorine is what’s behind burning eyes and irritated skin.

Total chlorine. The easy one.

It’s just the two added together.

Free chlorine+Combined chlorine=Total chlorine

Smell “chlorine”? A strong chlorine smell in the air means too much combined chlorine. That’s why we test total chlorine as well as free chlorine. If total is more than 0.2 ppm higher than free, it’s time to shock.

Cold-weather heads-up: most salt cells stop making chlorine when the water drops below about 50°F. If your pool stays open in cold weather, you may need packaged chlorine. Not a huge deal: algae doesn’t grow as easily in the cold.

⑤ HOW THE SALT CELL / CHLORINATOR WORKS

Inside your tiny chlorine factory.

No magic, just a little science and a pump that does its job. Here’s what’s going on behind the scenes.

01

How much chlorine? It depends.

Every pool is different

The amount of chlorine your pool needs varies with its size and with things like water temperature, swimmer load, direct sunlight and special water features.

02

Salt in, chlorine out. Repeat.

Sodium chloride does the work

The system needs a low concentration of dissolved salt (sodium chloride) in the water. Your salt system (ours is the AutoPilot Pool Pilot Evolve) uses that salt to generate the chlorine your pool needs to stay sanitized. After treating the water, the chlorine turns back into salt.

03

Where does the salt go? Not far.

Evaporation doesn’t count

Making chlorine doesn’t use up the salt, so you lose very little during a swimming season. Salt leaves through backwashing the filter, rainwater overflow, leaks and splashy swimmers. It does not leave through evaporation. The water goes; the salt stays.

04

Pump off = factory closed.

8+ hours a day

The pump has to run at a high enough flow rate for your chlorinator to make chlorine. Run time is one of the key factors in keeping sanitizer levels right. Most installations need at least eight hours of pump run time per day to filter and sanitize the water properly.

05

No salt, no chlorine.

New-salt checklist

The unit won’t make chlorine until the minimum amount of salt has been added to the pool. When you add salt, run the circulation pump continuously until it’s fully dissolved. Then reset the power at the power supply so the unit can accurately read the new salt level.

⑥ ADDING SALT

What kind, how much & how to add it.

The salt (or sodium chloride, NaCl, if you watch Jeopardy! at home) has to be more than 99% pure. The good news: most salt fits under that umbrella. Acceptable types:

  • Pool salt (naturally, recommended)
  • Non-iodized granular food-grade salt
  • Water softener pellets
  • Solar salt flakes

Pool salt and food-grade granular salt dissolve faster than pellets or flakes.

Skip these: rock salt and granular salt with iodine or rust preventatives. They contain high levels of impurities that can cause staining.

Four spoons heaped with white salt crystals on a dark surface

HOW MUCH SALT TO ADD

Test first. Then do the math.

Always check the salt level that’s already in the pool before adding any. For a new pool, 50 lbs of salt per 2,000 gallons raises the salt level by about 3,000 ppm.

10,000gallon pool (let’s pretend)
500 ppmsalt already in it
250 lbsof salt to reach 3,500 ppm

As mentioned earlier, the ideal range for the Pool Pilot Evolve is 3,500–4,500 ppm.

THE SALT-O-METER (POOL PILOT EVOLVE)

  • 6,000+Not normally recommended. Corrosion issues may result.
  • 3,500–4,500The sweet spot. Ideal salt range.
  • Under 2,700Lower efficiency and low chlorine production.
  • Under 2,300Low-salt safety cutoff. Chlorine production stops until you add salt.

How to add salt. Brush, dissolve, repeat.

  1. Add salt directly to the pool, over the main drain if you have one.
  2. Brush it around to help it dissolve, toward the main drain (again, if you have one). Don’t let salt pile up in one spot without brushing, or it may stain.
  3. Run the circulation pump continuously until the salt is fully dissolved. Then set the pump and filter back to their normal run time.
  4. Above ground pool? Spread the salt evenly around the edge of the pool and brush it toward the skimmer while it dissolves.
  5. New gunite (concrete) pool? Don’t run the Pool Pilot Evolve for 30 days after construction is finished. The plaster needs to cure first, or the salt could damage the finish.
  6. Overshot it? The only way to remove extra salt is to partially drain the pool and refill it with fresh water.

⑦ QUICK START

Quick start. Pool Pilot Evolve edition.

These instructions are for the Pool Pilot Evolve, the salt system we use for in-ground and above ground saltwater pools. For the full details, check out AutoPilot’s Pool Pilot Evolve page.

Pool Pilot Evolve + PPM1 Manifold
The gray AutoPilot Pool Pilot Evolve control box with a small LED display and up and down arrow buttons, next to its clear salt cell plumbed into white PVC pipe marked FLOW
The Pool Pilot Evolve: control box on the left, salt cell on the right.
01

Balance first.

Balance the water to the recommended chemistry and salt levels. The chlorinator can start right away, but the salt reading may be off until the pump has run for 24 hours to fully dissolve any new salt.

02

Start at 60%.

Use the △▽ buttons to set the sanitizer output to 60%. That’s the default starting point for a balanced pool pretreated to 2.0–4.0 ppm of chlorine.

03

Test every 3–4 days.

Right after start-up, check your sanitizer every 3–4 days and make small output adjustments to keep free chlorine at 2.0–4.0 ppm.

04

It won’t test for you.

Your chlorinator doesn’t measure or regulate the chlorine in your pool. You test the water now and then and adjust the output to match. Keep salt at 3,500–4,500 ppm.

WHAT DOES “OUTPUT %” MEAN?

It’s cell time, not chlorine strength.

The sanitizer output % is the amount of time the cell is switched on. The system cycles on and off (you’ll see a rotating character on the display), and you can set it anywhere from 0% to 100%. When it’s sized right for your pool’s gallons, the chlorinator is designed to make enough sanitizer to hold the recommended 2.0–4.0 ppm of free chlorine.

TO CHANGE THE OUTPUT %

  • Tap ▽ once for −1%, or △ once for +1%.
  • Hold either button to jump in 10% steps.
  • Watch the current output flash on the display. That means you can adjust it.
  • Let go when you hit the number you want. The unit goes back to normal operation.

Busy season? Turn it up.

When chlorine demand peaks (summer, rainy season or lots of swimmers), you may need to raise the sanitizer output setting. When demand is low, turn it down.

Need a boost? Shock it.

For extremely heavy chlorine demand, or to raise chlorine fast, you can add any type of chlorine, or a non-chlorine shock containing potassium monopersulfate. Avoid anything containing sodium bromide.

Balance still matters.

Water balance is the relationship between pH, total alkalinity and calcium hardness. Balanced water isn’t corrosive or scaling. Unbalanced water can damage equipment and pool surfaces. Sanitizers destroy harmful organisms, CYA (stabilizer) keeps the sun from eating your chlorine, and salt is what the Pool Pilot Evolve turns into chlorine.

⑧ READING THE DISPLAY

Blinky lights, decoded.

During normal operation, the Pool Pilot Evolve display shows the sanitizer output % you’ve selected and the cell polarity. Then there are three little status lights. Here’s what they’re telling you.

Salt light

The unit checks the water’s salt level at start-up and every 4 hours after that.

Green, solid: salt level is adequate (2,700–5,000 ppm). Green just means “OK.” Still aim for 3,500–4,500.

Green, flashing: salt is above 5,000 ppm. The unit is still making chlorine and won’t be damaged by high salt.

Red, solid: display shows Lo SaLt. Salt is between 2,300 and 2,700 ppm. The unit still makes chlorine, but at a lower output. Add salt as needed.

Red, flashing: display shows Add SaLt. Salt is below 2,300 ppm. No chlorine until the minimum salt level is reached.

Cell light

The cell is the part of the generator that actually makes the chlorine. After a few years (3–7 on average), it needs to be replaced.

Green, solid: the unit is operating normally.

Red, flashing: the unit isn’t making chlorine. The display shows CLN, CELL, SOON or CLN CELL, and the cell should be inspected. Calcium buildup on the cell blades, low salt and other things can reduce conductivity.

Flow light

Water flow and circulation are a big deal in any pool. This light shows whether water is flowing through the generator on its way back into the pool through the return.

Green, solid: the flow sensor sees enough water flow to make chlorine.

Red, flashing: display shows NO FLO. The sensor sees low or no flow through the cell. No flow, no chlorine.

⑨ WATER CHEMISTRY TERMS

The vocab list. No pop quiz, promise.

A quick cheat sheet for the words you’ll see on your test strip, your test results and our texts.

pH ACID OR BASE?

How acidic or basic the water is. Low pH (acidic, corrosive water) leads to eye and skin irritation and damages pool equipment. High pH leads to scaling, cloudy water and weak sanitizing.

Off-balance pH is also behind the strong smell, red eyes and dry, itchy skin that usually get blamed on “too much chlorine.” Salt pools tend to drift high, so check pH often.

Total alkalinity THE pH SHOCK ABSORBER

The water’s ability to resist changes in pH. It helps keep your pH in line. The Pool Pilot Evolve manual’s desired range is 80–100 ppm. Low alkalinity is aggressive (corrosive) and makes pH readings bounce around (pH bounce). High alkalinity can cause cloudy water and scale.

The chlorinator doesn’t affect total alkalinity. Other chemicals added to the pool and “out of balance” fill water do.

Calcium hardness HOW MUCH CALCIUM IS IN THERE

If calcium is too high, it can drop out of the water and form scale on your equipment and pool surface. If it’s too low, the water turns corrosive as it tries to balance itself out. It’ll “leach” minerals from everything it touches, damaging equipment and making swimming unpleasant.

Your chlorinator doesn’t change calcium hardness. Other chemicals added to the pool and “out of balance” fill water do.

Cyanuric acid (CYA) A.K.A. STABILIZER OR CONDITIONER

It goes by either trade name. It helps your chlorine last longer by protecting it from the sun’s UV rays. The sun is chlorine’s biggest enemy, and UV will destroy unprotected chlorine. With low CYA, your pool can burn through chlorine as fast as the cell makes it.

Salt pool tip: the Pool Pilot Evolve manual says 30–50 ppm, and that’s a fine floor. Saltwater pools generally do better with a higher range, around 60–80 ppm. A little extra sunscreen for all that freshly made chlorine. 🧴

Metals COPPER, IRON & FRIENDS

Some metals, like copper and iron, can cause chlorine loss. They can also stain your pool. When you test, metals should read 0 ppm. Some pool sanitizing programs are copper-based, but with a salt system, we don’t want them anywhere near our water.

Saturation index THE PRO-LEVEL FORMULA

Pool pros use this index to make sure your overall water chemistry doesn’t drift into corrosive or scaling territory. Either one can damage the cell, other equipment and your pool’s finish early. It’s made up of pH, temperature, calcium hardness and alkalinity, minus dissolved solids (mostly salt):

SI = pH + TF + CF + AF – TDSF

Do you need to know the saturation index? Nope. That’s our job. 😎

⑩ TROUBLESHOOTING CHEMICAL IMBALANCE

Numbers off? Here’s your fix.

Your water test results always come back as numbers in ppm. So what do you do with them? It might take a minute to get the hang of it, and that’s OK. It takes a few rounds before that “aha!” moment. Once you’re there, you’re there. And we’re always happy to walk you through it.

Salt pools drift this way ↑

pH (7.2–7.6)

TOO HIGH ↑

It’s basic. Cloudy water, weak chlorine, eye and skin irritation, scale buildup.

Fix: add muriatic acid or sulfuric acid.

TOO LOW ↓

It’s acidic. Equipment corrosion, eye and skin irritation, chlorine that gets used up fast.

Fix: add soda ash (sodium carbonate).

Total alkalinity (80–120 ppm)

TOO HIGH ↑

Constant acid demand and trouble keeping pH in range.

Fix: add muriatic acid or sulfuric acid.

TOO LOW ↓

Eye irritation, pH bounce, staining and metal corrosion.

Fix: add sodium bicarbonate.

Calcium hardness (200–400 ppm)

TOO HIGH ↑

Scale and cloudy water.

Fix: partially drain the pool and refill with fresh water to dilute.

TOO LOW ↓

Etched plaster and equipment corrosion.

Fix: add calcium chloride flakes.

Cyanuric acid (30–50 ppm per the manual; salt pools like 60–80)

TOO HIGH ↑

It takes more chlorine to keep the pool sanitized.

Fix: partially drain and refill with fresh water to dilute. Then check and adjust your salt (draining dilutes that too).

TOO LOW ↓

The sun’s UV rays destroy your chlorine.

Fix: add cyanuric acid: about 1 lb per 5,000 gallons (that raises CYA roughly 24 ppm). Then retest.

THE BOTTOM LINE

Pools are supposed to be fun.

Always remember: a pool is supposed to be relaxing and fun. If you’re having trouble controlling the water, your equipment is acting up, or anything else is getting in the way of the fun, contact us! We’ll help you every step of the way.

Stay salty (the good kind), Ryan

Line icons of a pool, a hot tub and a wave above the words Relax, Refresh, Repeat and swimwiththefin.com
Aerial view of a long turquoise backyard pool and spa surrounded by trees, lounge chairs and umbrellas

KEEP LEARNING

More from Pool School.

⑪ FREE WATER TESTING

Salty about your numbers? Let us test it.

Bring us a water sample from your pool or hot tub and we’ll test it for FREE. We’ll read the numbers, translate the chemistry and tell you exactly what your water (and your salt system) needs. No lab coat required.

Stock photos via Unsplash: David Vives, Jan Hildebrand, Ker. Y Lin, Kamakshi subramani, João Pedro Schmitz. Wave mark and “Relax • Refresh • Repeat” graphic by The Fin. Pool Pilot Evolve images from Ryan’s file (AutoPilot product images).