Algae outbreaks. Name it, then treat it. Green, mustard, black — and the pink one that isn’t even algae.
Not every green mood in the water is the same plant, and not every dark spot is a stain you can shock into submission. Outbreaks have types. Recovery has a routine. The routine changes, a little, depending on which uninvited guest actually showed up.
If the pool is already a swamp and you cannot see the bottom, that full rescue lives in Green to clean. Trust the process. Especially if the liner is vinyl. This page goes deeper on the types, why they show up, and how the cleanup differs. Every fact comes from official industry papers, public-health guidance, chemical labels, or manufacturer instructions. If they didn’t print it, we didn’t either.
By Ryan Musch
Director of Liquid Affairs, The Fin
POOL SCHOOL · ALGAE OUTBREAKS
What this story covers. How to tell green, mustard/yellow, and black algae apart, why the pink growth is not algae, how to tell an outbreak from a metal stain, why blooms start, and the recovery routine for each type — including vinyl-safe brushing and when to come see us. The full swamp process, especially on a neglected vinyl or above-ground pool, is Green to clean. Trust the process. Especially if the liner is vinyl. No prices, and no “we carry Brand X” claims. Your product labels always win.
“Algae is not a personality. It is a type. Name the guest before you start the party.”
— Ryan Musch, The Fin · authored for this page
THE LINEUP · OFFICIAL COLOR NAMES, PLUS ONE IMPOSTOR
Pool people sort algae by how it looks. That is not as sloppy as it sounds.
The PHTA Recreational Water Quality Committee’s “ABCs of Algae” uses an informal classification based on appearance, particularly color: green, mustard, and black. They also include the pink one, then immediately take its name away. That paper is the backbone of this page.
GREEN
The famous one. Pale to dark, sometimes overnight.
Green algae turns the water green and can knock visibility down to nearly nothing, which makes the pool slippery and unsafe. Official guidance says these outbreaks can happen overnight when free chlorine drops below 1 ppm. A light bloom and a neglected swamp are not the same amount of work, but they are usually the same family.
MUSTARD / YELLOW
The clingy one. Looks like dirt. Comes back.
Color can run from gray to dark green to mustard yellow. It likes the floor, the walls, and the quiet corners with poor circulation. When you brush it, it can look like clumps of dirt and cloud the water, then settle again. It is highly resistant to normal 1–4 ppm chlorine, which is why a “but I have chlorine” story is not a defense.
BLACK
Dark patches that do not brush off like a polite guest.
The least common of the three, official guidance says, and the stubborn one. It forms small, often irregular dark patches that are hard to brush loose, because the growth has long filaments and sends root-like shoots into the pool surface. On plaster that is one kind of fight. On a vinyl liner, the brush in your hand matters even more. We will get to that.
PINK / “WATER MOLD”
Not algae. Sorry to ruin the nickname.
PHTA is blunt: the red or pink slime people call “red algae” or “pink algae” is not algae. In a chlorine pool, that slime is usually from bacteria — the same family that leaves pink rings in a rarely used toilet or shower curtain. In a biguanide-treated pool, the pink color is from a fungus also called water mold, pink mold, or pink slime. Different guest. Different party.
BEFORE YOU SHOCK A “STAIN”
Green, brown or black is not a diagnosis. It might not be algae at all.
Color is a clue, not a conviction. The stains-and-metals class already made this point, and it still holds: iron, copper and manganese can paint a liner in shades that look a lot like an outbreak. Shocking a metal stain can set it, which is a very expensive way to learn a vocabulary word.
MORE LIKELY ALGAE
It brushes, clouds, or comes off the wall.
Mustard algae, official guidance says, can resemble clumps of dirt when brushed and then re-settle. Green algae is in the water as much as on the wall. If the “stain” moves, slimes, or turns the water opaque, you are probably in this story.
MORE LIKELY A STAIN
It sits there and ignores the brush.
A metal mark often stays put. Purple can be copper plus high stabilizer. Rusty brown or black can be iron or manganese, not black algae. If you are not sure, do not start a shock-and-scrub experiment. That is Stains and metals. Brown, green, purple or rusty — and it still might not be algae. Bring a sample if you want a second set of eyes.
WHY OUTBREAKS START · IT IS USUALLY NOT A MYSTERY
Low sanitizer is the usual villain. Circulation, stabilizer and phosphates can help it along.
PHTA’s algae paper says blooms commonly strike when sanitizer levels are low, and can also arise from poor circulation and filtration. Events that create high chlorine demand — a pool party, a rainstorm — can tip a barely maintained pool over the edge. The rest of the supporting cast is real, but it is supporting.
SANITIZER AND CIRCULATION
Below 1 ppm is an open invitation.
Green algae, officially, can appear overnight once free chlorine drops below 1 ppm. If the same bloom keeps coming back, the paper says free chlorine is likely still under 1 ppm, or a biguanide system is not being maintained. Poor circulation leaves quiet corners where mustard likes to sit. Once the pool is back in season, run the pump 16 hours a day. During a recovery, official shock and green-water directions often want the filter running continuously — 24 hours is a common labeled instruction — until the water has actually cleared.
STABILIZER AND PHOSPHATES
One can weaken the chlorine. The other is a snack.
If the chlorine “is there” on a test and the algae does not care, stabilizer may be the winter coat in July. That chapter is Chlorine lock. When the chlorine “isn’t working,” meet stabilizer. Phosphates are a different story, and official guidance is more careful than the internet. PHTA says phosphate is a nutrient algae and bacteria can use, but it does not directly create a chlorine demand — the phosphate ion does not react with free chlorine. What happens is this: if sanitizer and maintenance slip, the algae can use those phosphates as food and then the growing population eats more chlorine. Phosphate removers exist. They are a supporting mop, not a substitute for sanitizer. And if the pool is on a biguanide system, PHTA notes those sanitizers can react with phosphates and form a precipitate.
GREEN · THE RECOVERY THAT STARTED THIS WHOLE SCHOOL
Brush, shock to the label, filter like you mean it. A light bloom is not a swamp.
PHTA says green algae is the manageable one. Even a pea-green, zero-visibility outbreak is often controlled by a single shock of 5–10 ppm free chlorine. “Often” is doing some work in that sentence. A neglected swamp still needs the longer process in Green to clean. Trust the process. Especially if the liner is vinyl.
Balance first, especially pH. Shock labels and PHTA want pH in range before you superchlorinate, typically about 7.2 to 7.6. High pH makes chlorine lazy. Then vacuum debris — leaves eat sanitizer — and brush with a surface-compatible brush.
Shock per the label for your gallons. Broadcast with the pump running. Do not leave a pile of granules sitting on a vinyl liner. Brush anything that settles. Official algae directions often say add the treatment as close as possible to the growth, then brush, vacuum, and run it through the filter.
Run the filter continuously until the water clears. Twenty-four hours is a common official instruction after a shock for light algae. Brush again. Retest. A second labeled dose is allowed on many products after you retest — not a triple handful “just in case.”
Clean the filter when the dust settles. Backwash a sand or DE filter, or clean a cartridge, so you are not recirculating yesterday’s bloom. Then, if the label wants an algaecide after the shock residual is back in range, add it. Some shock directions say wait until free chlorine is 1–4 ppm before the algaecide goes in. The label in your hand wins.
MUSTARD / YELLOW · THE ONE THAT PACKS A SUITCASE
Brush before you treat. Repeat. And wash what went in the water.
Mustard algae has an outer shell and likes to sit on the floor, where a lot of the treatment never reaches it. It also hides in light fixtures, behind ladders, and inside the filter. That is why it can look gone on Tuesday and throw a reunion on Friday.
Brush first, thoroughly, then treat. Official guidance is specific: brushing before the chemicals go in is what exposes the cells. A polite once-over is not brushing.
Shock above a normal residual, then use the right helper. PHTA says mustard is highly resistant to 1–4 ppm chlorine. The usual official treatment is a shock of more than 5 ppm free chlorine, coupled with a metal-based algaecide, then a repeat three to five days later. Dual halogen- and ammonium-based systems are also described as effective. If the pool is on a biguanide system, do not reach for chlorine shock or a copper algaecide. That recovery is a polyquat algaecide plus hydrogen peroxide as the oxidizer — and it belongs with Biguanide. The pool that broke up with chlorine.
Backwash or clean the filter before you start, and chemically clean it after. Official guidance says that improves the treatment. Mustard in the filter is not a rumor. It is in the paper.
Wash the swimwear and the equipment that was in the pool during the outbreak. A manufacturer’s official mustard-algae directions include washing all swimwear and equipment that went in the water, because this stuff is clingy enough to hitch a ride back in. Follow a product or detergent label for the actual wash. Then keep the pool closed until the water is clear and the shock label’s re-entry test says you may swim.
BLACK · STUBBORN PATCHES, ESPECIALLY ON VINYL
Brush it, treat it, but do not sand the liner. Steel brushes are not a vinyl personality.
Official treatment for black algae is thorough brushing plus a spot application of granulated chlorine, which raises the concentration right on the attached growth. Some manufacturer care pages go further and talk about a stiff wire brush, more frequent brushing, continuous filtration, and repeated treatments. That advice was written with plaster and grout in mind as often as not.
On a vinyl liner, skip the steel. Liner makers are not subtle. Findlay and other vinyl-care guides say to avoid abrasive cleaning aids such as steel wool, sharp-bristled brushes, and scouring pads. LOOP-LOC wants only brushes and equipment designed with no sharp corners or edges that could damage the liner. A “surface-compatible brush” is the phrase on at least one official shock label, and it is the one we use here. Spot-dumping a pile of granules onto vinyl is also how you bleach a pattern — liner makers and shock labels both warn about undissolved product sitting on the surface. One manufacturer even prints that a particular black-algae spot treatment is for white plaster only. If the patches are on vinyl and they will not move, that is a shop conversation, not a wire-brush afternoon.
For a chlorine pool that is not a vinyl science experiment: brush thoroughly with a liner-safe or surface-compatible brush, follow the shock or black-algae label, keep the filter running, and plan on more than one round. Clean the filter so you are not putting the problem back in. Stay out until the label and a test agree.
PINK SLIME AND WATER MOLD · STILL NOT ALGAE
Treat the system you actually have. A green-algae recipe will not impress a fungus.
PHTA’s name for this guest is “red or pink algae,” and then they take it back: it is not algae. In chlorine-treated pools, the slime is produced by bacteria, often a photosynthetic species such as Rhodobacter. In biguanide-treated pools, the pink color is from a fungus, Paecilomyces lilacinus, which official language also calls water mold, pink mold, and pink slime.
We did not find a current official PHTA or label protocol that uses “white water mold” as a named, separate treatment, so we are not inventing one. What we can say is official: this is not green algae, it likes quiet, poorly circulated spots, and a biguanide pool should be treated as a biguanide pool. If you are on that system, start with Biguanide. The pool that broke up with chlorine. and come see us before anyone “just shocks it.” If you are on chlorine and you have pink slime in the skimmer, on a ladder, or in the filter, brush, clean the filter, get the sanitizer honest, and bring a sample if it keeps coming back.
SO THIS IS NOT A SEQUEL
Keep the sanitizer honest. Brush. Circulate. Prevention is boring in the best way.
THE WEEKLY HABITS
Chlorine in range, pump on a schedule, walls not ignored.
Hold a proper free-chlorine residual — official swimming-pool language is often 1–4 ppm, and at least 1 ppm is the line green algae loves to cross. Keep pH in range so that chlorine can actually work. Run the pump 16 hours a day. Brush the walls and floor weekly, even if you have a cleaner. Empty baskets. Keep the filter clean. After a party or a storm, test, and shock if the label’s conditions say so.
THE SUPPORTING CAST
A preventative algaecide, and a closer look if it keeps returning.
If green algae is a recurring problem, PHTA says better disinfection plus a weekly quaternary-ammonium algaecide is usually enough to prevent the next one. If the bloom is mustard or the chlorine “isn’t working,” test stabilizer and read Chlorine lock. When the chlorine “isn’t working,” meet stabilizer. Phosphates can be tested and reduced after the sanitizer is under control, as a nutrient cleanup, not as the first mop. And if the pool is a different sanitizer family, stay in that family.
WHEN TO HAND US THE KEYS
Some outbreaks are a shop morning. That is not a character flaw.
CALL US IF
You cannot see the bottom, or it will not stay gone.
A swamp, a vinyl liner you do not want to experiment on, mustard that returns after a by-the-book treatment, or black patches on vinyl are all good reasons to come in. Bring a water sample if you can. Recurring outbreaks are often a sanitizer, circulation, or stabilizer problem wearing an algae costume.
ALSO CALL US IF
You cannot tell stain from swamp, or the system is not chlorine.
Metal stains and algae can look like cousins. Pink slime on a biguanide pool is a different process. If you are not sure which sanitizer you are on, or which color is lying to you, we would rather look at it than have you invent a new recipe at the side of the yard.
PHTA Recreational Water Quality Committee, “ABCs of Algae,” Aqua Magazine, August 2018 — algae commonly strikes when sanitizer is low, and can also follow poor circulation and filtration or high-demand events such as parties and rain; close the pool when visibility is lost and restore clarity before re-entry; follow label directions and PPE; types and treatments used throughout this page: green (often a single 5–10 ppm shock; can bloom overnight below 1 ppm FC; recurring cases usually mean FC still below 1 ppm or a poorly maintained biguanide system; weekly quat algaecide for prevention); mustard/yellow (resistant to 1–4 ppm FC; shock above 5 ppm plus a metal-based algaecide, repeated 3–5 days later; or dual halogen- and ammonium-based systems; biguanide pools: polyquat plus hydrogen peroxide; brush before treating; hides in fixtures, behind ladders, and in the filter; backwash before and chemically clean the filter after); black (filamentous bacteria; thorough brushing and spot-applied granulated chlorine); pink/red is not algae (bacteria, often Rhodobacter, in chlorine pools; the fungus Paecilomyces lilacinus, also called water mold, pink mold, or pink slime, in biguanide pools).
PHTA RWQC Fact Sheet, “Source Water and its Effects on Pool and Spa Maintenance” (January 2020) — phosphate is an essential nutrient for bacteria and algae; it does not directly create a chlorine demand because the phosphate ion does not react with free chlorine; if maintenance and sanitization slip, algae and bacteria can use phosphates as a nutrient and the growing population may then raise chlorine demand; phosphate-removing products, typically a lanthanum salt, can precipitate phosphate for removal by filtration; biguanide sanitizers could react with phosphates and form a precipitate.
EPA-registered shock labels already verified for Green to clean. Trust the process. Especially if the liner is vinyl. — including HTH Dry Chlorinator Granular (EPA Reg. No. 1258-1069) and BioGuard Smart Shock (EPA Reg. No. 5185-493): pH in range before treatment; do not leave undissolved product on surfaces; brush with a surface-compatible brush; for algae, clean debris, broadcast, brush, vacuum, cycle through the filter; operate the pump and filter continuously for 24 hours after some labeled algae treatments; chemically clean the filter several days after a resistant-algae treatment on one label; do not enter until free chlorine is 1–4 ppm. HTH official green-water and shock pages: run the filter at least 24 hours until the water clears; some shock directions say wait until free chlorine is 1–4 ppm before adding algaecide.
HTH official algaecide education (manufacturer care / FAQ language on hthpools.com/collections/algaecides) — mustard algae: brush, follow the algaecide label, and wash all swimwear and equipment that was in the pool during the outbreak; prevention habits include chlorine 1–4 ppm, pH 7.2–7.6, weekly algaecide, regular shock, weekly brushing, a clean filter, and phosphate reduction if levels are high; very high CYA is described there as a condition that can allow algae despite seemingly adequate free chlorine (the longer version of that chapter is Chlorine lock. When the chlorine “isn’t working,” meet stabilizer.). That same page recommends a stiff wire brush and more aggressive shock dosing for black algae on what it describes as plaster or grout. We do not adopt the wire brush, or a “triple dose,” as a vinyl-liner instruction.
Vinyl-liner care: Findlay vinyl-liner care — avoid abrasive cleaning aids such as steel wool, sharp-bristled brushes, and scouring pads. LOOP-LOC liner care — use only vacuum heads, brushes, and maintenance equipment designed with no sharp corners or edges that could damage the liner; never use abrasive cleaners or pads. Latham and official shock labels warn that undissolved or concentrated chlorine sitting on vinyl can bleach, wrinkle, or weaken the liner. BioGuard’s pool-care guide states that a particular black-algae spot treatment (Spot Kill WP) should be used only on white plaster pools.
CDC Healthy Swimming — free chlorine and pH are the first defense; recommended pool pH 7.0–7.8 and a chlorine concentration of at least 1 ppm (at least 2 ppm if cyanuric acid is used); do not swim until the water and the product label say it is safe. Chemical-handling rules (never mix, add chemical to water never water to chemical unless a label says otherwise) are the same ones already cited in the green-to-clean class.
Sources checked November 15, 2026. Conflicts worth naming: official “spot-apply granular chlorine” and “wire-brush black algae” advice was written with plaster in mind as often as not, and it collides with vinyl-liner warnings against sharp or steel brushes and against leaving undissolved chlorine on the liner — this page sides with the liner on vinyl pools. Phosphate is a nutrient, not a direct chlorine demand, so we do not treat a phosphate remover as a cure-all. Some algaecide marketing says you may swim immediately after that product; shock labels and PHTA still want the pool closed until clarity is back and the re-entry test is met. “Often” a single 5–10 ppm shock controls green algae is not a promise for a neglected swamp. This is education, not a substitute for the label in your hand, your liner’s care guide, or a qualified technician. The Fin can test the water, help name the outbreak, and walk the recovery with you in Tulsa.
Green, mustard, black, or a pink mystery that will not take a hint?
Come see us at The Fin. Bring a water sample if you have one.