The Fin pool, spa & hot tubs, Tulsa OK The Fin Get a quote

STAINS AND METALS · LEARNING WITH THE FIN

Stains and metals.
Brown, green, purple or rusty — and it still might not be algae.

A pool can change color without growing a single plant. Iron, copper and manganese ride in on well water, a tired heater, a copper algaecide or a rain-washed stone deck. Then the sanitizer oxidizes them, and suddenly the water looks like tea, a science-fair experiment, or a bad mood.

Shocking a metal problem as if it were algae can make the stain show up faster. This page is about telling the two apart, testing, using a sequestrant the honest way, lifting a stain, and keeping it from coming back. Every fact comes from official sources: PHTA, EPA, CDC, liner-care guides and product directions. If they didn’t print it, we didn’t either.

An illustrated portrait of Ryan Musch of The Fin, in sunglasses and pink swim trunks, sitting in a backyard pool with a tropical drink while a small tan dog stands in the clear water beside him
By Ryan Musch Director of Liquid Affairs, The Fin POOL SCHOOL · STAINS AND METALS

This is Pool School, not a substitute for the product label in your hand, a metal test kit’s instructions, or your liner’s care guide. Color is a clue, not a courtroom verdict — PHTA says telling metal stains from organic ones can be tricky — so we test before we treat. If your pool is on a biguanide system, pause before you add anything: PHTA notes that biguanide sanitizers can react with iron and copper. That’s a different conversation; see our Biguanides story, or just text us.

A FRIENDLY HEADS-UP

The stain is not a dare. And the liner is paying attention.

Metals can stain and damage vinyl. LOOP-LOC and Findlay both want you to test for them, and LOOP-LOC says to use a metal treatment considered safe for vinyl. A stain-removal acid, dumped the wrong way, can do more harm than the stain. If a partial drain is on the table, talk to The Fin first — especially on a vinyl or above-ground pool. Our Green to Clean story walks through why pulling the plug is not a backyard first move.

“If the water turned the color of a penny, a bruise or a rusty nail, don’t assume you grew a garden. Test for metals before you empty the shock bag.”

Ryan Musch · Director of Liquid Affairs

THE MIX-UP

Why “just shock it” can make it worse.

Algae is a living thing. Metals are minerals. Chlorine is great at killing the first and excellent at showing off the second. If free chlorine is already in range and the water still looks stained or tea-colored, you may be looking at oxidized iron, copper or manganese — not a plant you missed.

TWO LOOK-ALIKES

Green is not always a bloom.

EPA links copper to blue-green staining. Iron shows up rusty, reddish or orange. Manganese runs black to brown. Purple water or a purple surface stain, PHTA says, can be copper reacting with high cyanuric acid — copper cyanurate. That’s chemistry, not pond scum. If you’re also wrestling with stabilizer, see our Chlorine Lock and Stabilizer story.

THE SPOT TEST

A vitamin-C detective, not a magic wand.

PHTA says a thorough history, a water test, and a spot test with ascorbic acid (vitamin C) or citric acid can help tell metal stains from organic ones. One catch: some organic stains, including those from iron bacteria, “disappear” with ascorbic acid and come right back once a chlorine residual is restored. If the stain does a disappearing act and then a reunion tour, call us before you buy a bigger bottle.

THE LINEUP

Iron, copper and manganese, in plain English.

PHTA’s Recreational Water Quality Committee names iron, copper, manganese and cobalt as the metals that typically cause pool and hot tub trouble (calcium and magnesium are a scale story, not this one). Color below follows EPA’s official staining language, plus PHTA on that purple copper-and-stabilizer combo. Color is a hint. The test is the answer.

IRON

Rusty, reddish, orange. The classic “tea water.”

EPA: rusty color, sediment, metallic taste, reddish or orange staining. It often arrives dissolved and nearly invisible, then turns on the rust show once chlorine or another oxidizer gets hold of it. PHTA also flags iron bacteria as a special case, and notes that iron can interfere with some UV systems — keep iron below 0.2 ppm if the UV maker says so.

COPPER

Blue-green stains. Sometimes a purple plot twist.

EPA: metallic taste and blue-green staining. A common backyard source is a gas heater’s copper heat exchanger when the water is out of balance. Copper algaecides and some mineral systems add it on purpose. CDC, as cited by PHTA, wants copper in pool and hot tub water no higher than 1.3 ppm — and PHTA warns that staining may start lower than that.

MANGANESE

Black to brown. The quiet one.

EPA: black to brown color, black staining, a bitter metallic taste. LOOP-LOC lists manganese with iron and copper as a liner-staining risk, especially in some water systems and rural areas. It doesn’t get the same press as rust, which is exactly how it ends up on the floor.

PURPLE IS A SPECIAL CASE PHTA: dissolved copper plus high cyanuric acid can produce a characteristic purple surface stain or purple-colored water, called copper cyanurate. If the pool went purple after a season of stabilizer and a copper source, test both — don’t just add more shock.

THE USUAL SUSPECTS

Where the metals sneak in.

PHTA is blunt: most metals in a pool show up after the fill, not just in it. Nearly all municipal and well supplies carry some iron, copper, manganese or cobalt, which is why they want the source water tested before you fill. Then the backyard keeps adding more.

THE WATER ITSELF

Well water, top-offs and leftover irrigation.

Fill water is the opening act. Well water and some municipal supplies bring metals with them. PHTA also flags irrigation with reclaimed or well water, and runoff. If total metals in the source water are over 0.2 ppm, they recommend treating that water before it goes in the pool. Untreated well water over 1 ppm? They say avoid using it to fill or top off.

THE EQUIPMENT

Heaters, ladders and a bonding wire you never think about.

Low pH (under 7) is acidic and can dissolve metals out of filtration equipment, heat exchangers and cementitious surfaces. Copper lives in many gas-heater cores. Iron, chromium and nickel live in stainless ladders, rails and light rings. If the bonding system isn’t doing its job, PHTA says metals in contact with the water can dissolve or discolor — galvanic corrosion, which gets a boost in salt water. Have the bonding checked if you see corrosion; sacrificial anodes can protect equipment but they dissolve into the water too.

THE YARD AND THE SHED

Stone, fertilizer, and the algaecide that arrived in a bottle.

Marble, flagstone and granite naturally contain iron and can leach into the pool after rain. Copper-based algaecides and mineral systems introduce metals on purpose. Lawn fertilizers can wash in if they land in the wrong place. Latham even warns that a stray iron nail or zinc roofing staple can stain a vinyl liner in no time.

GET A NUMBER

Test the water. Then test it honestly.

Findlay wants dissolved metals tested because they can stain vinyl directly or team up with calcium hardness and leave discolored deposits. LOOP-LOC says if metals are known or suspected, ask your pool supplier for a treatment considered safe for vinyl. We can test a sample. You can also test at home — with a grain of salt.

WHAT THE KIT SEES

Most metal tests only see the “free” metal.

PHTA: most readily available iron and copper tests measure only the free form of dissolved metal. Metals that are already sequestered, complexed, or floating around as oxidized particles often don’t show. Two-step total-metal tests, with a releasing or reducing agent, do a better job of seeing free, complexed and some oxidized metals. Follow the test maker’s instructions, not a hunch.

TEST THE SOURCE TOO

The hose deserves a quiz before the pool does.

PHTA recommends testing source water for metals before you fill. That’s especially true for a well, a fill after a drain, or a season of frequent top-offs. If the refill water is carrying metals, a beautiful stain-removal job is just intermission.

THE HOLDING PATTERN

Sequestrants are bodyguards. They are not bouncers who walk metals out the door.

The industry loves to call these products “metal removers.” PHTA would like a word. Sequestering agents are liquid chelators. They bond to dissolved metals and slow the sanitizer from oxidizing them, which helps keep stains off the surface. They do not, by themselves, take the metals out of the water.

WHAT THEY DO

They hold the metal still. Then you have to keep holding it.

The sanitizer and any secondary system slowly chew up the sequestering agent, so PHTA says you need regular maintenance doses on top of the first treatment, or the metals start oxidizing and staining again. Your filter usually will not catch sequestered metal particles — they’re typically too small. That’s a feature of the chemistry, not a broken filter.

HOW TO ADD ONE

Balance first. Circulate. Don’t shock right after.

Follow the label in your hand. A typical official example, HTH Metal, Stain & Scale Control, wants total alkalinity, pH and calcium hardness in range first, then the product added with the pump running. Brush anything that doesn’t dissolve. And don’t shock for at least 8 hours after you add it. The Fin’s in-season house rule is still at least 16 hours a day on the pump; a treatment day is not a day to let the water sit still. Don’t mix this product with other chemicals in a bucket.

TO ACTUALLY LOWER THE METALS PHTA lists only three reported ways to reduce dissolved metals in the water: replace a portion of the water with fresh, metal-free water; run the water through reverse osmosis; or use a water-insoluble adsorbent that binds the metals. A sequestrant is the holding pattern. A drain or a pro-level removal is the exit. On vinyl or above-ground pools, talk to The Fin before anyone opens a drain valve.

GETTING IT OFF THE WALL

Stain removers work in three steps. Skip one and the stain can RSVP yes.

PHTA’s well-established sequence is not a buffet. You lift the metal off the surface, then grab it in the water with a sequestrant, then get those metals out of the water. Leave step three out, and you have a very clean-looking dissolved-metal problem waiting to sit back down.

01 · LIFT

Get the stain off the surface.

Official stain-removal materials include ascorbic acid (vitamin C), citric acid, oxalic acid or a similar product, used as directed. HTH’s metal-control product also says it can remove fresh metal and copper stains — that’s “fresh,” not a decade of neglect, and the label still wins. PHTA: removing metal stains with muriatic acid should only be done by an experienced pool service professional, because it can permanently damage the surface.

02 · CHELATE

Grab what’s now in the water.

Once the stain leaves the wall, those metals are dissolved again. A sequestering agent is how you keep them from plating back onto the liner or plaster the minute the sanitizer goes back to work.

03 · REMOVE

Then get the metals out of the water.

See PHTA’s three exits above. A partial drain and refill with cleaner water is the one most homeowners hear about. It can be the right chemical move. It can also shrink, wrinkle or pull a vinyl liner, which is why this page and our Green to Clean story both say: talk to The Fin first, especially on an above-ground or vinyl pool.

KEEPING IT OFF IN THE FIRST PLACE

Prevention is boring. Stains are not.

BALANCE

pH is the most overlooked metal leak.

PHTA calls pH the most significant — and most overlooked — factor in keeping metals from leaching out of equipment and surfaces. Water below 7 is corrosive. Keep pH, alkalinity and hardness in the range your liner or plaster maker printed. Our Water Chemistry 101 story is the longer lesson; this page just needs you to know that sour water will go mining in your heater.

SANITIZER

A healthy residual means you need fewer copper algaecides.

PHTA: keep the primary sanitizer and stabilizer where they belong so you’re not reaching for a copper-based algaecide to mop up organics. Run the pump at least 16 hours a day in season. Test source water before a fill, and use a sequestrant as a holding pattern when metals are known or expected — including at opening, if the label calls for it.

THE HARDWARE

Don’t feed the pool nails, and don’t ignore rust.

Keep metal debris out of the pool. Watch walls, frames, ladders and heaters for corrosion. If something looks electrically or structurally off, that’s a bonding or equipment conversation, not a bigger scoop of shock. And if you’re on well water, treat it before it becomes the pool.

MORE POOL SCHOOL

This page has homework partners.

We kept this story on metals and stains. These other pieces hold the chemistry, the liners and the “please don’t drain that vinyl yourself” talk.

WATER CHEMISTRY 101

Water Chemistry 101.

pH, alkalinity, hardness and why out-of-range water starts picking fights with equipment — and with chlorine.

CAUSTIC & LINERS

Caustic Embrittlement & Pool Liners.

What unbalanced, overly aggressive water does to vinyl, and why a stain fix should not become a liner problem.

GREEN TO CLEAN

Green to Clean.

When it really is algae — and why a drain or a chemical dump is the wrong first move on vinyl.

BIGUANIDES

Biguanides.

If the pool broke up with chlorine, don’t treat metals as if it didn’t. Biguanide can react with iron and copper.

KEEP LEARNING

More from Pool School.

FINE PRINT

Where these facts live.

Sources checked November 15, 2026 (America/Chicago). Ryan portrait supplied by The Fin, from the approved-bio set (illustrated backyard-pool portrait with a small dog; not the bow-tie / blue-drink photo; not used on the last few pieces). Pull quote authored for this page. No prices included. This page is Pool School education, not a substitute for the product label, a metal-test kit’s instructions, or the liner’s care guide. Color is a clue, not a diagnosis: PHTA says differentiating metal stains from organic ones can be difficult, and EPA’s color language is from drinking-water aesthetic standards, not a pool-side paint chart. Sequestrants are often sold as “metal removers”; PHTA says they only chelate metals and do not take them out of the water. The 16-hour daily pump runtime is The Fin’s in-season service recommendation, consistent with our Caustic Embrittlement & Pool Liners, Pool Filters, and Multiport Filter Valve stories. PHTA lists replacing a portion of the water as one official way to lower dissolved metals, but liner and above-ground pool makers warn not to drain without a professional, because the liner can shrink, tear, or pull from the track — talk to The Fin before draining. This page does not treat copper’s 1.3 ppm CDC figure as a “stain starts here” line; PHTA says staining may occur at lower levels. It does not give a DIY muriatic-acid stain protocol. It does not assume every green pool is metals — algae is still algae, and our Green to Clean story covers that process.

Got water the color of a penny, a bruise or a rusty nail — and a liner you’d rather not experiment on?

Text Ryan, or bring us a sample. We’ll sort the stain from the swamp.